Sziasztok
Van egy :Samsung LE32 R32 BX/xeh lcd A kép felvillan és lekapcsol a háttérvilágitás.Megtaláltam benne egy szakadt inverter trafót ellenállás méréssel találtam meg.Most rendelés előtt állok a hq nál csak nem tudom hogy egy darabot elég e rendelnem mert van még egy gyanus trafó aminek 3.90k-3.91k helyett 3.88k az ellenállása ki tudom valahogy zárni hogy hibás vagy nem ez is?bekapcsolható igy a tv, hogy ki van forrasztva a hibás trafó?vagy ugyan ugy letilt esetleg tönkre mehet még valami ha igy próbálom ki?
Sziasztok.
Javitottam egy Philips TV-t,
itt volt szo rola.
Most ugy tunik, hogy ujabb problemam van vele.
Amikor elindult, egy Logitech Harmony taviranyitval probaltam, amit USB-n, PC-rol tanitok be, a helyes tipust kivalasztva.
Ez igy tokeletesen mukodik.
Gondoltam, veszek hozza egy olcso taviranyitot.
Rendeltem egy
398GR8BD-3NT tipusut, az eMAG-tol (persze a roman oldalrol)
Megjon a taviranyito... nem mukodik.
En ugy tudtam, hogy a Philips LCD-knel nem valtoztatattak a taviranyito kodolasat, esetleg plusz funkciokat adtak hozza, mas szoval egy regebbi taviranyito is mukodik egy ujabb TV-vel es forditva.
Csodalkoztam, de mivel a listaban az en modellem nem szerepel a kompatibilis keszulekek kozott, nem kuldtem vissza, bar 14 napig indoklas nelkul visszakuldhettem volna.
Kozben jartam az oszeren, talaltam egy Philips taviranyitot, ami ranezesre pont olyan mint az eredeti. Megvettem, nem mukodik.
Ennek a modellje:
398GR08BEPHN0008CR
Sebaj, rakerestem az eMAG-on es rendeltem egy ujabbat, amelyik azt irja, kompatibilis a TV-mmel:
RM-D1110 Utángyártott Philips Smart távirányító premium minőségben - eMAG.hu
Megerkezik... nem megy.
Az elemek nyilvan jok (ujak). A taviranyito mukodik, a telefon kamerajaval latom az IR-t. A TV mukodik a betanitott taviranyotoval. Csak a neki a szant taviranyitoval nem.
Nyilvan ezt mar visszakuldtem, hiszen ennek mennie kene.
Volt itthon egy Philips Smart taviranyito:
398GR10BEPHN0007DP
Ez sem vezerli.
Arra is gondoltam, hogy alaplapcsere volt, lehet mas taviranyito kellene hozza. De az alaplap olyan TV-bol szarmazik, amelyik kodja utolso betuig megegyezik az enyemmel, valamint a Logitech sem mukodtetne, ha erre a TV-re tanitottam.
Otleteket varok, mar unom, hogy egy ilyen olcso TV-hez hasznalhatatlan taviranyitokat vasaroljak.
Elore is koszonom
Minden jot,
Janos
Sziasztok!
Ennek a nem mai tvének, egyszer csak elment a hangja, pattant egyet és azóta semmi sem jön ki belőle. AV-én sincs hang, se be se kifelé. A sorkimenő körüli Khák miatt járattam. Nem tudom eldönteni hogy a végfok panelon van-e a gond vagy a scart panelon, a feltüntettet feszültségek meg vannak. Ic vagy tranzisztor hiba lehet?
Hello
I have on my table this sony kdl32ex600 with backlight issue. It's a common failure of this psu but i do not find any part faulted on this board.
The schematic it is almost the same, with minor differences with GE3B found at page 56 on this service manual:
https://elektrotanya.com/sony_kdl-32ex600_kdl-40ex600_kdl46ex600_chassis_az1-k.pdf/download.html
Uploaded only the page 56 from this sm to easing the search.
The red led it's flashing 2 times, meaning psu faulty. Indeed the led backlight does not light.
With the PSU outside of the tv, just with one resistance of 180ohm between standby ( pin 1 3,3V on connector CN6150 ) i get this values
on in:
starting with pin 1
1 +3,3V ST-BY
2 +3,3V AC_OFF_DET
3 +3,3V POWER_ON (with resistance 180ohm between pin1 and pin 3)
4 +12,56V AUDIO_12V
5 0V AUDIO_12V_GND
6 0V REG_12V_GND
7 0V REG_12V_GND
8 +12,6V REG_12V
9 +12,6V REG_12V
10 +0,1V BL_ERR
11 +3,3V BL_ON
12 0V DIMMER
13 0V DIMMER_DC
14 0V T-CON_Vcc_12V
15 0V T-CON_ON
All measure done at secondary ground point C6800 GND as reference.
Meanwhile, the led connected to CN6800 will remain with no light at all. The CN6800 will deliver positive 91V.
The negative branch will deliver at CN6801 ( both pin1 & 2 ) just -1V.
In the training manual found always in here at
https://elektrotanya.com/sony_kdl-32ex600_40ex600_46ex600_chassis_az1k_training%20manual.pdf/download.html
at page 56 will say "SHORT" at pin 12 DIMMER for testing the PSU, always with pin 3 POWER_ON connected to 3,3V ST-BY - pin1.
If i'll put a 180ohm resistance between GND and pin 12 DIMMER, then the tension on CN6800 will rise to +179V and the negative from the CN6801 will rise to -5V, the backlight led will light very very weak.
All tension from CN6805 will remain the same, except the BL_ERR will rise from +0,1V to +1,1V.
With only power_on pin 3 shorted by 180ohm resistance to the pin 1, i get this weak oscillation at emiter of Q6816 + Q6817
[URL=https://picturepush.com/public/16067400][IMG]https://www1.picturepush.com/photo/a/16067400/640/diverse/Q6816Q6817.jpg[/IMG][/URL]
With pin 12 DIMMER shorted ( always by a 180ohm resistance ) at GND, the oscillation will change from 250khz 1,6vpp to almost 70khz at 0,81Vpp. as below:
[URL=https://picturepush.com/public/16067401][IMG]https://www1.picturepush.com/photo/a/16067401/640/diverse/20181117-175255.jpg[/IMG][/URL]
Already checked the capacitors C6828 / C6830 together with D6805 / D6806.
Also checked the L6800 ( trafo ) and i've get 5,5mH instead of 5mH, i think it's ok.
All fuse checked, ok.
Q6814 and Q6801 tested under mosfet tester, ok.
[url=https://picturepush.com/public/16067402][img=https://www1.picturepush.com/photo/a/16067402/220/16067402.jpg][/url]
IC6800 & IC6801 gave +9V and respectively +2,49V
Already checked various components all over the board, i am out of ideas.
Any idea or help would be apreciated.