Service manuals, schematics, eproms for electrical technicians
EICO 147 SIGNAL TRACER
Type: 
(PDF)
(PDF)Size
755.8 KB
755.8 KB
Page
13
13
Category
METER
SERVICE MANUAL
METER
SERVICE MANUAL
If you get stuck in repairing a defective appliance download this repair information for help. See below.
Good luck to the repair!
Please do not offer the downloaded file for sell only use it for personal usage!
Looking for similar eico manual?
Good luck to the repair!
Please do not offer the downloaded file for sell only use it for personal usage!
Looking for similar eico manual?
Advertisements
Document preview [1st page]
Click on the link for free download!
Document preview [2nd page]
Click on the link for free download!
Advertisements
Please tick the box below to get download link:
- Also known:
EICO TRACER 147 SIGNAL
- If you have any question about repairing write your question to the Message board. For this no need registration.
- If the site has helped you and you also want to help others, please Upload a manual, circuit diagram or eeprom that is not yet available on the site.
Have a nice Day! - See related repair forum topics below. May be help you to repair.
Warning!
If you are not familiar with electronics, do not attempt to repair!
You could suffer a fatal electrical shock! Instead, contact your nearest service center!
Note! To open downloaded files you need acrobat reader or similar pdf reader program. In addition,
some files are archived,If you are not familiar with electronics, do not attempt to repair!
You could suffer a fatal electrical shock! Instead, contact your nearest service center!
so you need WinZip or WinRar to open that files. Also some files are djvu so you need djvu viewer to open them.
These free programs can be found on this page: needed progs
If you use opera you have to disable opera turbo function to download file!
If you cannot download this file, try it with CHROME or FIREFOX browser.
Translate this page:
Relevant METER forum topics:
Sziasztok!
A képen látható cuccról kellene kideríteni, hogy mi volt. Az egyik kép az eleje a másik a hátulja :)
http://kepfeltoltes.hu/140408/DSC_0560_www.kepfeltoltes.hu_.jpg
http://kepfeltoltes.hu/140408/DSC_0564_www.kepfeltoltes.hu_.jpg
Köszi. További kellemeset!
Sziasztok!
A Rádiótechnika 1981/12. számában /556.old./ Horváth József cikke alapján a szimpatikus kis áramkört megépítettem.De sajnos nem úgy működik ahogy kellene.
A 6db oszcillátor frekvenciáját nem lehet beállítani, mindegyik kb. másfél-kétszeres frekvencián működik. /Egyébként szabályozhatók de csak felfele/.
Pl. az 1 KHz helyett 1,5 KHz stb. Talán a 10 Hz-es oszcillátort lehet legközelebb állítani / a frekimérő:MASTECH MS8209/.
Lehet, hogy a frekimérő vezet félre?!
Kérem segítségeteket. Üdv::Niagara21
I have a long list of Workshop proven & used CPU-Emulator -Equipment
with full original-documentation for each part.
I do not know if it is allowed "here", to make such an offer
and because it is a long list of 6-8 different CPU-Emulator-POD's
please contact me via p.m. if any interest.
You will then get a lot of more detailed pictures from the actual packed devices
Attention!
THESE ARE EXPERT DEVICES for Whorkshop and Repair-Technicians
used to read & work with IC's, Schematics and Datasheets (DAILY) !
It's like working with each CPU-Device-PIN
with full Control over its external PCB-World (elctrical & timing & TRI-State),
seen and working like from inside the specific CPU to the external Periphery !!!!!
And this works , regarding DATA- ADRESS- & Control-BUS-Signals
for different interchangeable CPU-POD's with a common handling & usage on this
BASIC FLUKE9010A -Device, with script programmable and Tape Safe/Resore facility.
best regards Norbert
with full original-documentation for each part.
I do not know if it is allowed "here", to make such an offer
and because it is a long list of 6-8 different CPU-Emulator-POD's
please contact me via p.m. if any interest.
You will then get a lot of more detailed pictures from the actual packed devices
Attention!
THESE ARE EXPERT DEVICES for Whorkshop and Repair-Technicians
used to read & work with IC's, Schematics and Datasheets (DAILY) !
It's like working with each CPU-Device-PIN
with full Control over its external PCB-World (elctrical & timing & TRI-State),
seen and working like from inside the specific CPU to the external Periphery !!!!!
And this works , regarding DATA- ADRESS- & Control-BUS-Signals
for different interchangeable CPU-POD's with a common handling & usage on this
BASIC FLUKE9010A -Device, with script programmable and Tape Safe/Resore facility.
best regards Norbert
Az elmut héten kaptam eggy ilyen mérőezköszt. Megnéztem a belsejét, és láttam azt a mester munkát ami a
készülékben van (főleg a potenciométerk). Ezért szeretnék vele megtanulni mérni. Amint a képen látható csak
német nyelvűt kaptam hozzá.
Előre is köszönöm a segítséget. Gyula.
"Rajzot, service manualt, jobbra a "Keresem/WANTED" doboz "KATT IDE" gombján keresztül kérj!"
Similar manuals:
If you want to join us and get repairing help please sign in or sign up by completing a simple electrical test
or write your question to the Message board without registration.
You can write in English language into the forum (not only in Hungarian)!
or write your question to the Message board without registration.
You can write in English language into the forum (not only in Hungarian)!
E-Waste Reduce