Service manuals, schematics, eproms for electrical technicians
GOULD OS-4001 OUTPUT UNIT FOR-OS4000-DSO-GIVES-ANALOG-OUTS INSTR SM
Type: 
(PDF)
(PDF)Size
847.0 KB
847.0 KB
Page
19
19
Category
METER
SERVICE MANUAL
METER
SERVICE MANUAL
If you get stuck in repairing a defective appliance download this repair information for help. See below.
Good luck to the repair!
Please do not offer the downloaded file for sell only use it for personal usage!
Looking for similar gould manual?
Good luck to the repair!
Please do not offer the downloaded file for sell only use it for personal usage!
Looking for similar gould manual?
Advertisements
Document preview [1st page]
Click on the link for free download!
Document preview [2nd page]
Click on the link for free download!
Advertisements
Please tick the box below to get download link:
- Also known:
GOULD OS-4001 UNIT INSTR OS4001 OUTPUT OS 4001 FOROS 4000 FOR OS4000 DSO GIVES ANALOG OUTS
- If you have any question about repairing write your question to the Message board. For this no need registration.
- If the site has helped you and you also want to help others, please Upload a manual, circuit diagram or eeprom that is not yet available on the site.
Have a nice Day! - See related repair forum topics below. May be help you to repair.
Warning!
If you are not familiar with electronics, do not attempt to repair!
You could suffer a fatal electrical shock! Instead, contact your nearest service center!
Note! To open downloaded files you need acrobat reader or similar pdf reader program. In addition,
some files are archived,If you are not familiar with electronics, do not attempt to repair!
You could suffer a fatal electrical shock! Instead, contact your nearest service center!
so you need WinZip or WinRar to open that files. Also some files are djvu so you need djvu viewer to open them.
These free programs can be found on this page: needed progs
If you use opera you have to disable opera turbo function to download file!
If you cannot download this file, try it with CHROME or FIREFOX browser.
Translate this page:
Relevant METER forum topics:
Kedves Kollégák!
E jószág a sajátom.Kb két hete használtam, veszem elő aztán előbb az
egyik sugár,majd a másik is eltünt.Olyan mint amikor egyenfesz kerül a
függőleges eltérítőre. Az elektronsugár fönt van a holdon :-(((
Valószínüleg itt is ez a gond.Az egyik végtranyó/fet?/ munkaellenállása
hideg,de a tranzisztorok jók,megcseréltem őket.Ez még a teljesen
tranzisztoros darab,békebeli.
Esetleg rajza lenne valakinek?
Köszi,üdv,kovácsa
Üdv mindenkinek!
Nemrégiben hozzájutottam a a fenti névvel ellátott szkóphoz.
De sajnos a függőleges eltérítésével gondok vannak. A kalibráló jelet,ami természetesen másik szkóppal ellenőrzésre került és ami 1Vpp amlitúdójú azt sajna csupán 0.7Vpp-ként jeleníti meg.
Megkísérelném megjavítani de nem találtam kapcsolási rajzot. Ha valaki rendelkezne vele kérem ossza meg velem,és szivesen vennék néhány jó tanácsot.
Előre is köszönöm.
Üdvözlet
Hello to everybody,
I have bought a defective Gould oscilloscope DSO420. At the beginning of the repair the power fuse was blown immediately after inserting the power plug: The RF-filter connector was shorted. Okay, ignore the RF-filter for now.
Some leaked capacitors were within the power supply, all renewed as well as the NiMh accumulator.
Now most of the scope is running:: All LED at the front as well they are switchable and the screen of the scope was lightened th but only a vertical line is shown. No horizontal deflection at all.
The circuit I have attached, all semiconductor are renewed, no change. The electrolytics are renewed, no change. Allways a vertical stroke. Does anyone have an idea?
Regards from Hamburg
Jens
I have bought a defective Gould oscilloscope DSO420. At the beginning of the repair the power fuse was blown immediately after inserting the power plug: The RF-filter connector was shorted. Okay, ignore the RF-filter for now.
Some leaked capacitors were within the power supply, all renewed as well as the NiMh accumulator.
Now most of the scope is running:: All LED at the front as well they are switchable and the screen of the scope was lightened th but only a vertical line is shown. No horizontal deflection at all.
The circuit I have attached, all semiconductor are renewed, no change. The electrolytics are renewed, no change. Allways a vertical stroke. Does anyone have an idea?
Regards from Hamburg
Jens
Üdv!
A fent említett szkóp a sajátom, mérés közben pattant egyet valami és egy pont lett csak a csövön középen.
Egy képcsőfűtésen mértem épp jelalakot!
Amit eddig találtam: D 219 (1N4148 mindkét irányba vezetett, de nem full zárlattal)
TR 221 (BC212) Collektor-emitter zárlat
Ezeket az alkatrészeket cseréltem, de a hiba maradt.
Van valakinek ötlete merre tovább?
+/-20V rendben, 170V rendben, X kimeneten 37-34-es pontok között kb 12V van.
Similar manuals:
If you want to join us and get repairing help please sign in or sign up by completing a simple electrical test
or write your question to the Message board without registration.
You can write in English language into the forum (not only in Hungarian)!
or write your question to the Message board without registration.
You can write in English language into the forum (not only in Hungarian)!
E-Waste Reduce